%
O0001(BUFFER SET-UP)(20/3/98)
G00G17G21G40G49G69G80G90 
H00
M70
#133=0.
M99
                                                                                                                         
O0002(THREADING) 
(HEL. INT. MACRO)
(G65 P2 D- Z- T- R- S- F-) 
(SPECIFY D CODE FOR RAD OFFSET)
(FOR INT. TOOL RAD=+)
(FOR EXT. TOOL RAD=-)
(D=RADIUS #7)
(Z=DEPTH #26)
(T=Z PITCH #20)
(R=Z SET UP #18) 
(S=RETRACT AMOUNT & DIRECTION)(#19)
(END POINT 9 O-CLOCK)
(F=FEED RATE)(#9)
#103=#5003 
#3=0.
#21=#7-#[2000+#4307] 
G91G0X-#21 
G90G0Z#18
#104=#26-#18 
WHILE[#3GT#104]DO1 
IF[[#3-#20]LT#104]THEN#20=-[#104-#3] 
G91G2Z-#20I#21F#9
#3=#3-#20
END1 
G1X#19 
G90G0Z#103 
G91X[#21-#19]
G90
M99
                                                                                                                         
O0003(PROFILE MACRO) 
(G66/G65 P3 A- Z- Q- R- F-)
(A=PROFILE PROG NO #1) 
(Z=Z DEPTH #26)
(Q=DEPTH OF CUT #17) 
(R=Z SET UP #18) 
(F=FEED RATE #9) 
#103=#5003(READ Z) 
#104=#18 
G90G0Z#104 
WHILE[#104GT#26]DO1
#104=#104-#17
IF[#104LT#26]THEN#104=#26
G90G1Z#104F#9(G1)
F#9
M98P#1 
END1 
G90G0Z#103 
M99
                                                                                                                         
O0004(HEL INTERPOLATION) 
(MILLING SAME AS 2)
(HEL. INT. MACRO)(INTERNAL)
(G65 P4 D- Z- T- R- S- F-) 
(SPECIFY D CODE FOR RAD OFFSET)
(D)
(S RELIEF 019) 
(F)
#101=#5001 
#102=#5002 
#103=#5003 
#105=#20 
#21=#7-#[2000+#4307] 
G91G0X-#21 
G90G0Z#18
#104=#5003 
WHILE[#104GT#26]DO1
IF[[#104-#105]LT#26]THEN#105=#104-#26
G91G3Z-#105I#21F#9 
#104=#5003 
END1 
G3I#21 
G1X#19 
G90G0Z#103 
X#101Y#102 
M99
 
 
                                                                                                                         
O0005(CIR INTERPOLATION) 
(G65 P5 S- D- T- F-) 
(CAN BE CONTROLED BY MACRO #3) 
(G65 P3 A5. Z- Q- R- F- S- D- T-)
(SPECIFY D FOR RAD OFFSET) 
(S=INSIDE BORE RAD #19)
(D=BORE RAD #7)
(T=DEPTH OF CUT #20) 
(F=FEED RATE #9) 
#101=#5001 
#102=#5002 
#3=#19 
#4=#[2000+#4307] 
G0X[[#101-#3]+#4]
WHILE[#3LT#7]DO1 
#3=#3+#20
IF[#3GT#7]THEN#3=#7
G1X[[#101-#3]+#4]F[#9/4] 
G3X[[#101-#3]+#4]Y#102I[#3-#4]F#9
END1 
G0X#101Y#102 
M99
 
 
                                                                                                                         
O0006(STEPPED CIR. INT)
(G65 P6 Z- Q- R- S- D- T- F-)
(SPECIFY D FOR RAD OFFSET) 
(Z DEPTH #26)
(Q DEPTH OF CUT #17) 
(R STARTING POSITION #18)
(S #19)
(D #7) 
(T #20)
(F FEED #9)
#101=#5001 
#102=#5002 
#103=#5003 
#105=#17 
#13=#[2000+#4307]
G90G0Z#18
#104=#5003 
WHILE[#104GT#26]DO1
IF[[#104-#105]LT#26]THEN#105=#104-#26
G91G1Z-#105F[#9/2] 
#104=#5003 
#3=#19 
WHILE[#3LT#7]DO2 
#3=#3+#20
IF[#3GT#7]THEN#3=#7
G90G1X[[#101+#3]-#13]F[#9/2] 
G91G3I-[#3-#13]F#9 
G90
END2 
G0X#101
END1 
Z#18.
G90G0X#101Y#102Z#103.
M99
 
 
                                                                                                                         
O0007(SPIRAL CIR. INT.)
(FIX)
(G65 P7 S- T- F-)
(Z CAN BE CONTROLED BY P3) 
(G65 P3 A7. Z- Q- R- S- T- F-) 
(SPECIFY D CODE FOR RAD OFFSETS) 
(S=RADIUS #19) 
(T=WIDTH OF CUT #20) 
(F=FEED RATE #9) 
#101=#5001(X START)
#102=#5002(Y START)
#104=0.(START ANGLE) 
#106=#[2000+#4307](RAD OFFSET) 
#105=0.(RADIUS)
F#9(FEED RATE) 
WHILE[#105LT[#19-#106]]DO1 
#104=#104+10.
#105=#105+[#20/36.]
IF[#105GT[#19-#106]]THEN#105=#19-#106
/IF[#104GE360.]THEN#104=#104-360.
#111=COS[#104]*#105
#112=SIN[#104]*#105
G90G03X[#101+#111]Y[#102+#112]R[#105*2.]F#9
END1 
#3=1 
#105=#19-#106
WHILE[#3LE3]DO1
#104=#104+130. 
/IF[#104GE360.]THEN#104=#104-360.
#111=COS[#104]*#105
#112=SIN[#104]*#105
G03X[#101+#111]Y[#102+#112]R#105 
#3=#3+1
END1 
G1X#101Y#102(G3 R[#105*0.5]) 
G0 
M99
 
 
                                                                                                                         
O0008(NPT THREADING) 
(HEL. INT. MACRO)
(INTERNAL THREADING) 
(SPECIFY D CODE FOR RAD OFFSET)
(G65 P8 D- Z- T- R- F-)
(D=RADIUS #7)
(Z=Z DEPTH #26)
(T=PITCH #20)
(R=Z SET UP #18) 
(F=FEED RATE #9) 
#101=#5001 
#102=#5002 
#103=#5003 
#3=0.
G90G0Z#18
#104=#26-#18 
#21=#7-#[2000+#4307] 
#105=#20*0.03125(1:16/2) 
G1X[#101+#21]F#9 
WHILE[#3GT#104]DO1 
#4=-45.
WHILE[#4GE-360.]DO2
#18=#18-[#20/8.] 
#21=#21-[#105/8.](360./45.=8.) 
#24=COS[#4]*#21
#25=SIN[#4]*#21
G2X[#101+#24]Y[#102+#25]Z#18R[#21+[#105/32.]]
#4=#4-45.
END2 
#3=#3-#20
END1 
G90G0X#101Y#102
Z#103
M99
 
 
                                                                                                                         
O0009(POLAR CO-ORD MACRO)
(G65 P9 I J K W) 
(G65 P9 I J K W U H) 
(I=X CENTER POINT #4)
#114=#4
(J=Y CENTER POINT #5)
#115=#5
(K=POLAR RADIUS #6)
#116=#6
(W=POLAR ANGLE #23 +=C.C,-=C)
#117=#23 
(U=INCRAMENTAL ANGLE #21)
(H=REPITION #11) 
IF[#11LT1.]THEN#11=1.
#3=0.
WHILE[#3LT#11]DO1
#117=#117+#21
#104=COS[#117]*#116
#105=SIN[#117]*#116
X[#114+#104]Y[#115+#105] 
#3=#3+1. 
END1 
M99
 
 
                                                                                                                         
O0010(2 ND DEPTH CONTROLE) 
(M98 P10)
#18=#18-#17
IF[#18LT#26]THEN#18=#26
G90G1Z#18F[#9/3] 
F#9
M99
 
 
                                                                                                                         
O0011(STEP H/S DRILLING) 
(G65 P11 Z- K- Q- R- F-) 
(Z=DRILLING DEPTH)(#26)
(K=SMALL PECKING DEPTH)(#6)
(Q=PECKING DEPTH)(#17) 
(R=Z STARTING POINT SET UP)(#18) 
(F=FEED RATE)(#9)
#103=#5003 
G90G0Z#18
#104=#18 
#105=#18 
WHILE[#104GT[#26-#17]]DO1
IF[#104LT#26]THEN#104=#26
G73Z#104Q#6R#105F#9
#105=#104+0.6
#104=#104-#17
END1 
G0Z#103
M99
                                                                                                                         
O0012(SLOT MILLING)
(G65 P12 X- Y- Z- Q- R- F-)
(X#24 Y#25 Z#26 Q#17 R#18 F#9) 
#101=#5001(X START)
#102=#5002(Y START)
#103=#5003(Z START)
#104=#18 
G90G0Z#104 
WHILE[#104GT#26]DO1
#104=#104-#17
IF[#104LT#26]THEN#104=#26
F#9
G1Z#104/F[#9/4](G1)
G1X#24Y#25F#9
IF[#104EQ#26]GOTO99
#104=#104-#17
IF[#104LT#26]THEN#104=#26
G1Z#104/F[#9/4](G1)
G1X#101Y#102F#9
N99END1
G0Z#103
X#101Y#102 
M99
                                                                                                                         
O0013
N1G54S800T2M3
G90G0X-35.Y80.Z350.
G43Z20.H1M16 
G83Z-25.Q2.R2.F40
X-12.Y80.
X12.Y80. 
X35.Y80. 
X35.Y0.
X-35.Y0. 
X-35.Y-80. 
X0.Y-80. 
X35.Y-80.
G0Z350.H00 
G91G28Z0.M6
N2G54S600T3M3
G90G0X-35.Y80.Z350.
G43Z20.H3
G83Z-25.Q1.R2.F40
X-12.Y80.
X12.Y80. 
X35.Y80. 
X35.Y0.
X-35.Y0. 
X-35.Y-80. 
X0.Y-80. 
X35.Y-80.
G0Z350.H00 
G91G28Z0.M6
N3G54S500T4M3
G90G0X-35.Y80.Z350.
G43Z20.H3
G83Z-25.Q2.R2.F40
X-12.Y80.
X12.Y80. 
X35.Y80. 
X35.Y0.
X-35.Y0. 
X-35.Y-80. 
X0.Y-80. 
X35.Y-80.
G0Z350.H00 
G91G28Z0.M6
N4G54S150T1M3
G90G0X-35.Y80.Z350.
G43Z20.H4
G83Z-25.Q2.R2.F40
X-12.Y80.
X12.Y80. 
X35.Y80. 
X35.Y0.
X-35.Y0. 
X-35.Y-80. 
X0.Y-80. 
X35.Y-80.
G0Z350.H00M17
G91G28Z0.Y0.M6 
M30
                                                                                                                         
O0014(Y SLOT WITH X WIDTH) 
(G65P14 U- V- Y- Z- Q- R- F-)
(U=WIDTH #21)
(V=X DEPTH OF CUT #22) 
(Y#25 Z#26 Q#17 R#18 F#9)
#101=#5001(X START)
#102=#5002(Y START)
#103=#5003(Z START)
G90G0Z#18
#3=0(CONTROLER X)
WHILE[#3LT[#21/2]]DO1
WHILE[#18GT#26]DO2 
#18=#18-#17
IF[#18LT#26]THEN#18=#26
G1Z#18F[#9/2]
G1Y#25F#9
#18=#18-#17
IF[#18LT#26]THEN#18=#26
Z#18F[#9/2]
Y#102F#9 
END2 
#3=#3+#22
IF[#3GT[#21/2]]THEN#3=#21/2
G1X[#101+#3] 
Y#25 
X[#101-#3] 
Y#102
X#101
END1 
G0Z#103
M99
 
 
                                                                                                                         
O0015(X SLOT WITH Y WIDTH) 
(G65P15 U- V- X- Z- Q- R- F-)
(U=WIDTH #21)
(V=Y DEPTH OF CUT #22) 
(X#24 Z#26 Q#17 R#18 F#9)
#101=#5001(X START)
#102=#5002(Y START)
#103=#5003(Z START)
G90G0Z#18
#3=0(CONTROLER Y)
WHILE[#3LT[#21/2]]DO1
WHILE[#18GT#26]DO2 
#18=#18-#17
IF[#18LT#26]THEN#18=#26
G1Z#18F[#9/2]
G1X#24F#9
#18=#18-#17
IF[#18LT#26]THEN#18=#26
Z#18F[#9/2]
X#101F#9 
END2 
#3=#3+#22
IF[#3GT[#21/2]]THEN#3=#21/2
G1Y[#102-#3] 
X#24 
Y[#102+#3] 
X#101
Y#102
END1 
G0Z#103
M99
 
 
                                                                                                                         
O0016(POCKET MILLING ?)
(POSITIVE ONLY)
(X)(24)(U)(21) 
(Y)(25)(V)(22) 
(Z)(26)
(T)(20)
(Q)(17)
(R)(18)
(F)(9) 
#101=#5001 
#102=#5002 
#103=#5003 
G90G0Z#18
WHILE[#18GT#26]DO1 
#18=#18-#17
IF[#18LT#26]THEN#18=#26
G1Z#18F[#9/3]
IF[#21GE#22]GOTO10 
IF[#22GT#21]GOTO20 
N10G91G1Y-[#22/2]F#9 
X#21 
Y#22 
X-#21
GOTO90 
N20G91G1X[#21/2]F#9
Y#22 
X-#21
Y-#22
N90G90X#101Y#102 
END1 
G0Z#103
M99
 
 
                                                                                                                         
O0055(EXT CIRCULAR INTERPOLATION)
(G65 P55 Y Z S D T F)
#101=#5001 
#102=#5002 
#103=#5003 
#3=#19(S START OD) 
#4=#[2000+#4307] 
G0X[[#101-#3]-#4]Y#25
Z#26 
G1Y0.F#9 
WHILE[#3GT#7]DO1 
#3=#3-#20
IF[#3LT#7]THEN#3=#7
IF#3=#7THEN#20=0.
G3X[[#101+#3]+#4]Y#102I[#3+#4+[#20/2]] 
G3X[[#101-#3]-#4]Y#102I-[#3+#4]
END1 
G1Y-[#25]
G0Z#103
G0X#101Y#102 
M99
                                                                                                                         
O0120(PISTON MILL AND REAM)
M98P1(X50.)(09/2007) 
N1G54S400T2M3(WOODRUFF CUTTER) 
G90G0X0.Y0.Z350. 
G43Z30.H1M16 
Z-13.(Z-12.7)
X-6. 
G1X-18.75F50 
G0X6.
G1X18.75 
G0X0.
G0Z350.H00 
G91G28Z0M6 
N2G54S1000T3M3(C DRILL)
G90G0X-29.4Y0.Z350.
G43Z30.H2M16 
G81Z-2.R2.F30
X29.4
G0Z350.H00 
G91G28Z0M6 
N3G54S1300T4M3(5.8 DRILL)
G90G0X29.4Y0.Z350.(29.74)
G43Z30.H3M16 
G81Z-19.Q2.R2.F40
X-29.4 
G0Z350.H00 
G91G28Z0M6 
N4G54S150T1M3(06 REAMER) 
G90G0Y0.X-29.4Z350.
G43Z30.H4M16 
G81Z-14.8R2.F40
X29.4
G0Z350.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0150(V150 SAE12/16) 
M98P1(06/06) 
(JIG P)(X 848.59)(X-25.4)
(G54)(-280.9)(-444.2)
(G55 G57 Z-438.5 Y-281.05) 
(G56 Z-455.3)
(M24)(1 0)(03,04)
M00
(1)
N1G54S500T2M3(015.5DRILL)
G90G0X0.Y0.Z300. 
G43Z10.H1M16 
G83Z-55.Q7.R-35.F60
G00X-100.Z400.H00
G91G28Z0.M6
N2G54S600T3M3(L/HOLD BAR)
G90G0X0.Y0.Z300. 
G43Z10.H2M16 
G0Z-12.
G1Z-48.F40 
S400Z-50.5F20
G0Z10. 
G00X-100.Z400.H00
G91G28Z0.M6
N3G54S100T4M3(1.3/16-12 SAE14) 
G90G0X0.Y0.Z400. 
G43Z10.H3M16 
G84Z-37.R-10.F211. 
G00X-100.Z400.H00
G91G28Z0.M6
N4G54S500T5M3(SAE BAR) 
(SAE-12 Z-30.5)
(SAE-16 Z-31.) 
G90G0X0.Y-43.Z300. 
G43Z10.H4M16 
G82Z-25.P200R5.F30 
Y43. 
G0X-100.Z400.H00 
G91G28Z0.M6
N5G54S100T6M3
(1.1/16-12 SAE12)
(1.5/16-12 SAE16)
G90G0X0.Y43.Z300.
G43Z10.H5M16 
G84Z-22.F211.
Y-43.
G0X-100.Z400.H00 
G91G28Z0.M6
N6G54S600T7M3
(1.1/2 BSP S.SEAL BAR) 
G90G0X0.Y43.Z300.
G43Z5.H6M16
G1Z-1.2F30.
X4.
G3I-4.F80. 
G0Z5.
Y-43.
G1Z-1.2F30.
X4.
G3I-4.F80
G0Z20. 
G0X-100.Z400.H00 
G91G28Z0.M6
(M24)(2 -90) 
M00
(2)
N7G55S300T8M3(B FACE CUTTER) 
G90G0X-5.Y120.Z300.
G43Z3.H7M16
G1Y0.F80 
G0Y120.Z4. 
Z1.5 
G1Y0.
G0Y120.Z3. 
Z0.
G1Y0.
G0X-100.Z400.H00 
G91G28Z0M6 
N8G55S450T9M3(P/RELIEF.BAR)
G90G0X0.Y39.5Z300. 
G43Z80.H8M16 
G82Z-46.4P500R2.F40
G0X-100.Z400.H00 
G91G28Z0.M6
N9G55S100T10M3(1.3/16-16 TAP)
G90G0X0.Y39.5Z350. 
G43Z80.H9M16 
G84Z-22.R10.F158.
G0X-100.Z400.H00 
G91G28Z0.M6
N10G55S500T11M3(20 U-DRILL)
G90G0X0.Y0.Z300. 
G43Z80.H10M16
G73Z-100.Q2.R2.F100
G0X-100.Z400.H00 
G91G28Z0.M6
N11G55S600T12M3(22. B/BAR) 
G90G0X0.Y0.Z300. 
G43Z80.H11M16
G81Z-96.R2.F90 
G0X-100.Z400.H00 
G91G28Z0.M6
N12G55S600T13M3(S.SEAL B/BAR)
(041.5 X 4.7)
G90G0X0.Y0.Z300. 
G43Z80.H12M16
G89Z-4.7P500R2.F30 
G0X-100.Z400.H00 
G91G28Z0.M6
N13G55S800T14M3(05.DRILL)
G90G0X-18.Y18.Z300.
G43Z20.H13M16
G83Z-25.Q7.R2.F50. 
X18. 
Y-18.
X-18.
G0X-100.Z400.H00 
G91G28Z0.M6
N14G55S200T7M3(M6-1TAP)
G90G0X-18.Y18.Z300.
G43Z20.H14M16
G84Z-16.R10.F200.
X18. 
Y-18.
X-18.
G0X-100.Z400.H00 
G91G28Z0.M6
(M24)(-180)
M00
(3)
N7G55S300T8M3(B FACE CUTTER) 
G90G0X-5.Y130.Z300.
G43Z-41.5H7M16 
G1Y-30.F80 
G0X-100.Z200.
(M24)(-270)
M00
(4)
G0X-5.Y95.Z3.
G1Y-30.F80 
G0Y95.Z4.
Z1.5 
G1Y-30.
G0Y95.Z3.
Z0.
G1Y-30.
G0X-100.Z400.H00 
G91G28Z0M6 
N8G55S450T9M3(P/RELIEF.BAR)
G90G0X0.Y-39.5Z300.
G43Z80.H8M16 
G82Z-46.4P500R2.F40
G0X-100.Z400.H00 
G91G28Z0.M6
N9G55S100T10M3(1.3/16-16 TAP)
G90G0X0.Y-39.5Z350.
G43Z80.H9M16 
G84Z-22.R10.F158.
G0X-100.Z400.H00 
G91G28Z0.M6
N10G55S500T11M3(20. U-DRILL) 
G90G0X0.Y0.Z300. 
G43Z80.H10M16
G73Z-100.Q2.R2.F100
G0X-100.Z400.H00 
G91G28Z0.M6
N11G55S600T12M3(021.9B/BAR)
G90G0X0.Y0.Z300. 
G43Z40.H11M16
G81Z-96.R2.F90 
G0X-100.Z400.H00 
G91G28Z0.M6
N12G55S600T13M3(S.SEAL B/BAR)
(041.5 X 4.7)
G90G0X0.Y0.Z300. 
G43Z80.H12M16
G89Z-4.7P500R2.F30 
G0X-100.Z400.H00 
G91G28Z0.M6
N13G55S800T14M3(05.DRILL)
G90G0X-18.Y18.Z300.
G43Z20.H13M16
G83Z-25.Q7.R2.F50. 
X18. 
Y-18.
X-18.
G0X-100.Z400.H00 
G91G28Z0.M6
N14G55S200T1M3(M6-1 TAP) 
G90G0X-18.Y18.Z300.
G43Z20.H14M16
G84Z-16.R10.F200.
X18. 
Y-18.
X-18.
G0X-100.Z400.H00 
G91G28Z0.M6
/M98P151(M24 5-8)
G28Y0
(M24)(180) 
M00
(9)
M17
M30
                                                                                                                         
O0152(INLET M10,3/8)(05/06)
(DATUM X137. Y55.)(-619.2) 
M98P1
N1G57S1200T2M3(C DRILL)
G90G68X0.Y0.R1.
G90G0X-17.5Y25.Z350. 
G43Z20.H1M16 
G83Z-7.Q3.R2.F40 
X17.5
X31.Y-25.
X-31.
G0Z400.H00 
G91G28Z0.M6
N2G57S850T3M3(08. DRILL) 
G90G0X-17.5Y25.Z350. 
G43Z20.H2M16 
G83Z-35.Q2.R2.F40
X17.5
X31.Y-25.
X-31.
G0Z400.H00 
G91G28Z0.M6
N3G57S200T4M3(45. DEG BIG) 
G90G0X-17.5Y25.Z350. 
G43Z20.H3M16 
G82Z-2.8P100R0.F40(-2.5,3.2) 
X17.5
X31.Y-25.
X-31.
G0Z400.H00 
G91G28Z0.M6
N4G57S100T1M3(3/8-16UN)
G90G0X-17.5Y25.Z350. 
G43Z20.H4M16 
G84Z-21.R5.F158.75 
X17.5
X31.Y-25.
X-31.
G0Z400.H00M17
G69
G91G28Y0Z0M6 
M30
                                                                                                                         
O0155(V150 INLET SIDE SAE20) 
M98P1(01/96) 
(DATUM X137. Y55.)(G57)(Z-619.7) 
(D 38.8 U43.5 Z-26.6)
(OUTLET Y-6.2 Z-24.) 
(T2M6) 
(M00)
N1G57S450T2M3(SAE-20 BAR)
G90G0X0.Y0.Z350. 
G43Z100.H1M16
G82Z-28.5P500R2.F60(-27.3) 
G0Z400.H00 
G91G28Z0M6 
N2G57S100T1M3(1.5/8-12UN)
G90G0X0.Y0.Z350. 
G43Z100.H2M16
G84Z-22.R10.F211.6 
G0Z400.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0160(0-RING GROOVE) 
(S/SECTION Z-631.96) 
(OUTLET Z-644.76)
M98P1(02/06) 
(OUTLET Z-644.5 ON INLET JIG)
N16G58S350T17M3(027.)
G90G0X.2Y38.Z350.
G43Z20.H16M16
G82Z-1.3P50R2.F20. 
X0.Y-33. 
G0G49Z400.H00
G91G28Z0M6 
N17G58S250T16M3(032.)
G90G0X0.Y0.Z350.(FLOAT Y-0.5)
G43Z20.H17M16
G82Z-1.3P50R2.F20. 
G0G49Z350.H00M17 
/G91G28Z0M6
/N3G58S300T1M3(019. DRILL) 
/G90G0X0.Y-33.5Z350. 
/G43Z20.H3M16
/G83Z-20.Q2.R2.F80 
/G0Z400.H00
G91G28Y0Z0M6 
M17
M30
                                                                                                                         
O0301(START MANIFOLD TOP)
M98P1(M10, 1/4)(10/06) 
(DATUM TOP RIGHT)
(B/V Z-576.2)
N1G57S800T2M3(C DRILL) 
G90G0X-8.Y-8.Z350. 
G43Z20.H1M16 
G81Z-18.5R-12.F20
Y-272. 
X-78.
X-50.5Y-235.R2.Z-3.(X-51.87) 
X-43.Y-95. 
X-42.Y-35.(X-42.34)
X-78.Y-8.R-12.Z-18.5 
G0Z350.H00 
G91G28Z0M6 
N2G57S700T3M3(08.5 DRILL)
G90G0X-8.Y-8.Z350. 
G43Z20.H2M16 
G83Z-58.Q2.R-12.F80
Y-272. 
X-78.
Y-8. 
G0Z350.H00 
G91G28Z0M6 
N3G57S100T4M3(M10-1.5) 
G90G0X-8.Y-8.Z350. 
G43Z20.H3M16 
G84Z-27.R-8.F150.
Y-272. 
X-78.
Y-8. 
G0Z350.H00 
G91G28Z0M6 
N4G57S900T5M3(06. DRILL) 
G90G0X-42.Y-35.Z350. 
G43Z10.H4M16 
G83Z-24.Q2.R2.F80
X-43.Y-95. 
X-50.5Y-235. 
G0Z400.H00 
G91G28Z0M6 
N5G57S450T6M3(011. DRILL)
G90G0X-42.Y-35.Z320. 
G43Z10.H5M16 
G83Z-16.Q2.R2.F60
X-43.Y-95. 
X-50.5Y-235. 
G0Z400.H00 
G91G28Z0M6 
N6G57S100T1M3(1/4-18 NPT)
G90G0X-42.Y-35.Z320. 
G43Z20.H6M16 
G84Z-8.R5.F141.11
X-43.Y-95. 
X-50.5Y-235. 
G0Z400.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0302(START MAN. R.T.) 
M98P1(06/06) 
(G58 X785.15)(Y-281.03)(Z-489.87)(G59  Z-392.8)(X-23.5)(X-25.) 
(DIA 50 ISCAR) 
(1 016.5 DRILL)
(2 019. F/BAR) 
(3 GROOVE BAR D20) 
(4 5.2 DRILL)
(5 M6-1 TAP) 
(6 011. DRILL) 
(7 1/4-18 NPT) 
(8 SAE#10 S BAR) 
(9 5/8 ROUGH)/(15. E/MILL) 
(10 5/8 REAMER)
(11 C-10-3 BAR)
(12 7/8-14 UN) 
(13 V45 RELIEF)
(14 3/4-16)
(BONNET SIDE FIRST)
M00(01)
GOTO20 
/N1G58S700T2M3(50 ISCAR) 
/G90G0X0.Y170.Z350.
/G43Z50.H1M16
/Z0. 
/G1Y-170.F150. 
/G0G49X-100.Z400.H00 
/G91G28Z0M6
N1G58S300T2M3(015. DRILL)
G90G0X0.Y45.Z350.
G43Z50.H1M16 
G73Z-92.Q1.R3.F60
G0G49X-100.Z400.H00
G91G28Z0M6 
N2G58S600T3M3(019.B/BAR) 
G90G0X0.Y45.Z350.
G43Z50.H2M16 
G81Z-90.R2.F40(Z-88.)
G0G49X-100.Z400.H00
G91G28Z0M6 
N3G58S1500D20T4M3(GROOVE)
(D20 9.2)(DIA 23.6)
G90G0X0.Y45.Z350.
G43Z20.H3M16 
Z2.
G65P3A5.Z-5.8Q7.R0.5S9.3D11.8T3.F50. 
G0G49X-100.Z400.H00D00 
G91G28Z0M6 
N4G58S1000T5M3(05.2 DRILL) 
G90G0X0.Y45.Z350.
G43Z10.H4M16 
G91X18.Y18.
G90G83Z-28.Q2.R2.F80 
G91Y-36. 
X-36.
Y36. 
G90G0G49X-100.Z400.H00 
G91G28Z0M6 
N5G58S150T6M3(M6-1)
G90G0X0.Y45.Z350.
G43Z10.H5M16 
G91X18.Y18.
G90G84Z-18.R5.F150.
G91Y-36. 
X-36.
Y36. 
G90G0G49X-100.Z400.H00 
G91G28Z0M6 
N6G58S600M3T7(011. DRILL)
G90G0X0.Y105.Z320. 
G43Z10.H6M16 
G73Z-68.Q2.R2.F90
G73X0.Y-30.R2.Z-25.F60 
X0.Y-95.Z-45.F90 
G0G49X-100.Z400.H00
G91G28Z0M6 
N7G58S100T8M3(1/4-18 NPT)
G90G0X0.Y-30.Z320. 
G43Z50.H7M16 
G84Z-7.R5.F141.11
G0G49X-100.Z400.H00
G91G28Z0M6 
N8G58S400M3T9(SAE 10 S BAR)
G90G0X0.Y-95.Z350. 
G43Z50.H8M16 
G82Z-16.8P50R2.F40.
Y105.Z-7.
G0G49X-100.Z400.H00
G91G28Z0.M6
N9G58S300M3T10(5/8 R)
G90G0X0.Y-95.Z350. 
G43Z50.H9M16 
G81Z-35.R-15.F30 
G0G49X-100.Z400.H00
G91G28Z0M6 
N10G58S130M3T11(5/8 REAMER S)
G90G0X0.Y-95.Z350. 
G43Z50.H10M16
G81Z-34.R-10.F30 
G0G49X-100.Z400.H00
G91G28Z0M6 
N11G58S400T12M3(C-10-3 BAR)
G90G0X0.Y105.Z350. 
G43Z50.H11M16
G82Z-56.P50R-6.F40 
G0G49X-100.Z400.H00
G91G28Z0M6 
N12G58S100T1M3(7/8-14 UN)
G90G0X0.Y105.Z350. 
G43Z50.H12M16
G84Z-25.R0.F181.43 
G84Y-95.Z-13.R5.F181.43
G0G49X-100.Z400.H00M17 
G91G28Y0Z0M6 
M30(2ND SIDE)
/N1G58S700T4M3(050 ISCAR)
/G90G0X0.Y170.Z350.
/G43Z50.H1M16
/Z0. 
/G1Y-170.F200
/G0G49X-100.Z400.H00 
/G91G28Z0M6
/N3G58S600T3M3(019.F/BAR)
/G90G0X0.Y-45.Z350.
/G43Z20.H2M16
/G81Z-46.R2.F40
/G0G49X-100.Z400.H00 
/G91G28Z0M6
N20G58S1500D20T6M3(GROOVE) 
G90G0X0.1Y-45.08Z350.
G43Z20.H3M16 
Z2.
G65P3A5.Z-5.8Q7.R0.5S9.3D11.8T3.F50. 
G0G49X-100.Z400.H00D00 
G91G28Z0M6 
N6G58S400T11M3(011. DRILL) 
G90G0X0.Y95.Z350.
G43Z50.H6M16 
G73Z-45.Q2.R2.F100 
Y30.Z-40.
G0G49X-100.Z400.H00
G91G28Z0.M6
N11G58S400T12M3(C-10-3 BAR)
G90G0X0.Y95.Z350.
G43Z50.H11M16
G82Z-50.3P50R2.F40 
G0G49X-100.Z400.H00
G91G28Z0M6 
N12G58S100T13M3(7/8-14 UN) 
G90G0X0.Y95.Z350.
G43Z50.H12M16
G84Z-19.R5.F181.4286 
G0G49X-100.Z400.H00
G91G28Z0M6 
N13G58S400T14M3(V45 RELIEF)
G90G0X0.Y30.Z350.
G43Z50.H13M16
G82Z-34.5P50R2.F50 
G0G49X-100.Z400.H00
G91G28Z0M6 
N14G58S100T4M3(3/4-16 UN TAP)
G90G0X0.Y30.Z350.
G43Z50.H14M16
G84Z-18.R5.F158.75 
G0G49X-100.Z400.H00
G91G28Z0M6 
N4G58S750T5M3(05.2 DRILL)
G90G0X0.Y122.Z350. 
G43Z20.H4M16 
G83Z-14.Q2.R2.F60. 
X15. 
Y-122. 
X0.
G0G49X-100.Z350.H00
G91G28Z0.M6
N5G58S150T1M3(M6-1 TAP)
G90G0X0.Y122.Z350. 
G43Z20.H5M16 
G84Z-10.R5.F150. 
X15. 
Y-122. 
X0.
G0G49X-100.Z350.H00M17 
G91G28Y0Z0.M6
M30
M00
M30
N71G59S600T8M3(011. DRILL) 
G90G0X0.Y17.Z320.
G43Z50.H7M16 
Z10.M00
G73Z-20.Q2.R5.F60
G0G49X-100.Z320.H00
G91G28Z0M6 
N8G59S100T7M3(1/4-18 NPT)
G90G0X0.Y17.Z320.
G43Z50.H8M16 
G84Z-5.R8.F141.11
M00
G0G49X-120.Z320.H00
G91G28Y0Z0M6 
M00
M17
M30
                                                                                                                         
O0603(600 SUB) 
G91G1X-1.4F100 
G3I1.4 
M98P604L20(12. MM) 
G3I1.4 
G0X1.4 
G90
M99
 
 
                                                                                                                         
O0604(600 SUB) 
G3Z-0.6I1.4F200
M99
 
                                                                                                                         
O0605
(DIA 91.1 & DRILL) 
G98P1(PRAM1623 TO 0) 
(DATUM TOP RIGHT CORNER) 
(G57 Z-589.5)(Y-220.72)(5/95)
N1G57S950D27T22M3(050. 75.DEG I) 
(D11 25.1) 
G90G0X-130.Y-26.Z300.
G43Z20.H21M16
Z0.
G1X30.F400 
G0Y-74.
G1X-130. 
G0Y-55.Z-4.
G1G41X-96.27F200.
Y-50.F300. 
G2X-96.27Y-50.I46.27F420.
G1Y-45.
G0Z20. 
G0G40X-200.Z400.H00
G91G28Z0M6 
N2G57S1200D28T23M3(032 I)
(D12 16.)(ROUGHING)(DIA 100.)
G90G0X-130.Y-55.Z350.
G43Z20.H22M16
G65P3A607.Z-20.Q3.2R-4.F360. 
G0G40X-100.Z400.H00
G91G28Z0M6 
N3G57S2500D29T24M3(032.I)
(D13 16.)
G90G0X-120.Y-55.Z300.
G43Z20.H23 
Z-4.M16
G1G41X-95.55F600 
Y-50.
G2X-95.55Y-50.I45.55 
G1Y-45.
G0Z20. 
G0G40X-200.Z400.H00
G91G28Z0M6 
N4G57S2400D30T25M3(012. 45DEGI)
(D14 11.9) 
G90G0X-120.Y-55.Z300.
G43Z20.H24M16
Z-9.5
G1G41X-96.F550.
Y-50.
G2X-96.Y-50.I46. 
G1Y-45.
G0Z20. 
G0G40X-200.Z400.H00
G91G28Z0M6 
N5G57S750T21M3(010.DRILL)
G90G0X-30.Y-20.Z300. 
G43Z10.H25M16
G73Z-45.Q2.R2.F110 
X-58.Y-50. 
G0Z20. 
G0X-200.Z400.H00M17
G91G28Y0.Z0.M6 
M30
                                                                                                                         
O0607(605 SUB ALT CUTTER)
(DIA 100.PROFILE)
G1G41X-100.F#9 
Y-50.
G2X-100.Y-50.I50.
G1Y-45.
G0G40X-130.Y-55. 
M99
                                                                                                                         
O0608(600 SPOOL) 
M98P1(10/07) 
(G57)(X522.06)(Y-280.8 Z-522.8)
M00
(1 0)(NO 7)
N1G57S1000T2M3(C DRILL)
G90G0X9.8Y0.Z350.
G43Z20.H1M16 
G81Z-5.R2.F50
G0Z350.H00 
G91G28Z0M6 
N2G57S600T3M3(05. DRILL) 
G90G0X9.8Y0.Z350.
G43Z20.H2M16 
G83Z-25.Q2.R2.F50
G0Z350.H00 
G91G28Z0M6 
N3G57S1500T4M3(014. M) 
G90G0X50.Y20.Z350. 
G43Z10.H3M16 
G65P12Y-20.Z-5.15Q1.3R0.F100.
G0X80. 
G65P12Y-20.Z-5.15Q1.3R0.F100.
G0X110.
G65P12Y-20.Z-5.15Q1.3R0.F100.
G0X80. 
M00
(2 -45.) 
Y10. 
G65P12Y-20.Z-5.15Q1.5R-0.65F100. 
G0X50.Y20. 
M00
(3 45.)
G65P12Y-10.Z-5.15Q1.5R-0.65F100. 
G0Z-5.14 
G1Y0.F1000 
M00
(4 0.F50)
G0Z2.
X80. 
G1Z-5.14F100 
M00
(5 -45.F50)
G0Z300.H00 
G91G28Z0M6 
N4G57S1500M3T1(06. SC E/MILL)
G90G0X27.Y14.Z350. 
G43Z20.H4M16 
G65P12Y-14.Z-5.2Q0.8R0.F60.
M00
(6 -135.)
G0Y12. 
G65P12Y-14.Z-5.2Q0.8R0.F60.
M00
(7 -90.) 
G0Y10. 
G65P12Y-10.Z-5.2Q2.R-2.F60.
G0Z300.H00 
M00
(8 0)
G91G28Y0Z0M6 
M17
M30
                                                                                                                         
O0610(600 BLOCKS VICE) 
M98P1(11/2007) 
(DATUM MIDDLE RIGHT) 
N1G54S500T2M3(015.5 DRILL) 
G90G0X-15.Y32.Z400.
G43Z20.H1M16 
G65P11Z-108.K1.Q5.R6.F80.
G0X-100.Z450.H00 
G91G28Z0M6 
N2G54S200T1M3(019.75 DRILL)
G90G0X-15.Y32.Z450.
G43Z40.H2M16 
G65P11Z-110.K1.Q5.R6.F60.
G0X-100.Z450.H00 
G91G28Y0Z0M6 
M17
M30
                                                                                                                         
O0611(TOP) 
(DATUM MIDDLE RIGHT) 
N3G54S300T4M3(019.DRILL) 
G90G0X-15.Y30.Z350.
G43Z20.H3M16 
G83Z-45.Q2.R2.F50
Y0.
Y-30.
G0X-100.Z400.H00 
G91G28Z0.M6
N4G54S400T3M3(012.2 DRILL) 
G90G0X-15.Y-30.Z400. 
G43Z40.H4M16 
G83Z-82.Q3.R-40.F60
Y0.
Y30. 
G0X-100.Z400.H00 
G91G28Z0.M6
N3G54S300T5M3(019.DRILL) 
G90G0X-15.Y30.Z400.
G43Z10.H3M16 
G82Z-47.5P500R-42.F50
Y0.
Y-30.
G0X-100.Z400.H00 
G91G28Z0M6 
N5G54S150T6M3(021.5 DRILL) 
G90G0X-15.Y-30.Z350. 
G43Z10.H5M16(SHOLDER)
G82Z-3.P500R2.F60
Y0.
Y30. 
G0X-100.Z400.H00M17
G91G28Z0.M6
N6G54S100T7M3(R1/2 14 TAP) 
G90G0X-15.Y30.Z350.
G43Z30.H6
G84Z-20.R8.F181.4
Y0.
Y-30.
G0X-100.Z400.H00 
G91G28Z0.M6
N7G54S200T3M3(45.C/SINK) 
G90G0X-15.Y-30.Z350. 
G43Z10.H7M16 
G82Z-9.5R-7.P100F30
Y0.
Y30. 
G0X-100.Z400.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0612(SIDE FIRST SAME AS FIRST)
(DATUM MIDDLE RIGHT) 
N8G54S600T10M3(010.DRILL)
G90G0X-15.Y5.Z300. 
G43Z10.H8M16 
G73Z-20.Q2.R2.F80
G0X-100.Z400.H00 
G91G28Z0M6 
N10G54S600T11M3(017.S/DRILL) 
G90G0X-15.Y5.Z350. 
G43Z15.H10M16
G82Z-4.5P500R2.F30 
G0X-100.Z450.H00 
G91G28Z0M6 
N11G54S900T12M3(05.DRILL)
G90G0X-29.Y44.Z300.
G43Z20.H11M16
G83Z-25.Q2.R2.F80
Y20. 
G0X-100.Z400.H00 
G91G28Z0M6 
N12G54S150T7M3(M6. 1TAP) 
G90G0X-29.Y44.Z300.
G43Z20.H12M16
G84Z-12.R5.F150. 
Y20. 
G0X-100.Z400.H00 
G91G28Z0M6 
N7G54S200T13M3(45.C/SINK)
G90G0X-29.Y44.Z300.
G43Z10.H7M16 
G81Z-1.2R0.F20 
Y20. 
G81X-15.Y5.Z-7.3R-5. 
G0X-100.Z400.H00 
G91G28Z0M6 
N13G54S200T14M3(60.C/SINK) 
G90G0X-15.Y32.Z300.
G43Z10.H13M16
G82Z-12.8P500R-10.F30
G0X-100.Z400.H00 
G91G28Z0M6 
N14G54S1700T8M3(18.6 B/BAR)
G90G0X-15.Y32.Z350.
G43Z15.H14M16(MIDDLE)
G0Z-14.
M98P603
G0Z-44.
M98P603
G0Z50. 
G0X-100.Z450.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0613(SIDE SECOND) 
(DATUM MIDDLE LEFT)
N8G54S600T9M3(010.DRILL) 
G90G0X15.Y5.Z300.
G43Z10.H8M16 
G73Z-20.Q2.R2.F80
Y-20.Z-50. 
G0X-100.Z400.H00 
G91G28Z0M6 
N9G54S800T10M3(013.S/DRILL)
G90G0X15.Y-20.Z350.
G43Z50.H9M16 
G82Z-3.P500R2.F30
G0X-100.Z400.H00 
G91G28Z0M6 
N10G54S600T11M3(017.S/DRILL) 
G90G0X15.Y5.Z350.
G43Z15.H10M16
G82Z-4.5P500R2.F30 
G0X-100.Z450.H00 
G91G28Z0M6 
N11G54S900T12M3(05.DRILL)
G90G0X29.Y44.Z300. 
G43Z20.H11M16
G83Z-25.Q2.R2.F80
Y20. 
G0X-100.Z400.H00 
G91G28Z0M6 
N12G54S150T7M3(M6. 1TAP) 
G90G0X29.Y44.Z300. 
G43Z20.H12M16
G84Z-12.R5.F150. 
Y20. 
G0X-100.Z400.H00 
G91G28Z0M6 
N7G54S200T13M3(45.C/SINK)
G90G0X29.Y44.Z300. 
G43Z10.H7M16 
G81Z-1.2R0.F20 
Y20. 
G81X15.Y5.Z-7.R-5. 
G81Y-20.Z-5.R-3. 
G0X-100.Z400.H00 
G91G28Z0M6 
N13G54S200T14M3(60.C/SINK) 
G90G0X15.Y32.Z300. 
G43Z10.H13M16
G82Z-12.8P500R-10.F30
G0X-100.Z400.H00 
G91G28Z0M6 
N14G54S1700T8M3(18.6 B/BAR)
G90G0X15.Y32.Z350. 
G43Z15.H14M16(MIDDLE)
G0Z-14.
M98P603
G0Z50. 
G0X-100.Z450.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0618(600 SPOOL BIG VICE)
M98P1(FIRST OP)(11/2007) 
(G57)(Z- ) 
N1G57S1000T2M3(C DRILL)
G90G0X0.Y-9.8Z350. 
G43Z20.H1M16 
G81Z-2.R2.F50
G0Z350.H00 
G91G28Z0M6 
N2G57S600T3M3(05. DRILL) 
G90G0X0.Y-9.8Z350. 
G43Z20.H2M16 
G83Z-25.Q2.R2.F50
G0Z350.H00 
G91G28Z0M6 
N3G57S1500T1M3(014. M) 
G90G0X-20.Y-50.Z350. 
G43Z10.H3M16 
G65P12X20.Z-5.15Q3.R0.F100.
G0Y-80.
G65P12X20.Z-5.15Q3.R0.F100.
G0Y-110. 
G65P12X20.Z-5.15Q3.R0.F100.
G0Z300.H00 
G91G28Y0Z0M6 
M30
                                                                                                                         
O0619(600 SPOOL 2ND OP 45D LEFT) 
M98P1
N3G57S1500M3(014. M) 
G90G0X-20.Y-50.Z350. 
G43Z10.H3M16 
G65P12X20.Z-5.15Q3.R0.F100.
G0Z300.H00M17
G91G28Y0Z0 
M30
                                                                                                                         
O0620(600 SPOOL 3ND OP 45D RIGHT)
M98P1
N3G57S1500T4M3(014. M) 
G90G0X-20.Y-80.Z350. 
G43Z10.H3M16 
G65P12X20.Z-5.15Q3.R0.F100.
G0Z300.H00 
G91G28Z0M6 
N4G57S1500M3T3(06. SC E/MILL)
G90G0X-14.Y-27.Z350. 
G43Z20.H4M16 
G65P12X14.Z-5.2Q1.3R0.F60. 
G0Z300.H00M17
G91G28Y0Z0M6 
M30
                                                                                                                         
O0621(600 SPOOL 4TH OP 135D RIGHT) 
M98P1
N4G57S1500M3(06. SC E/MILL)
G90G0X-14.Y-27.Z350. 
G43Z20.H4M16 
G65P12X14.Z-5.2Q1.3R0.F60. 
G0Z300.H00M17
G91G28Y0Z0 
M30
                                                                                                                         
O0701(GAUGE AND TANK)
M98P1
(X&Y MIDDLE)(X75. Y120.) 
(G57 Z-615.7)
N1G57S1200T2M3(C DRILL)
G90G0X0.Y0.
G68R-90. 
G90G0X-48.5Y70.Z400. 
G43Z80.H1M16 
G81Z-8.R2.F60
X11.Y97. 
/X-11.Y-97.
/X48.5Y-70.
G0G49Z400.H00
G91G28Z0M6 
N2G57S650T3M3(08.4 DRILL)
G90G0X-48.5Y70.Z400. 
G43Z80.H2M16 
G83Z-20.Q2.R2.F40
/X48.5Y-70.
G0G49Z400.H00
G91G28Z0M6 
N3G57S150T4M3(1/8-27NPT) 
G90G0X-48.5Y70.Z400. 
G43Z80.H3M16 
G84Z-7.R10.F141.111
/X48.5Y-70.
G0G49Z400.H00
G91G28Z0M6 
N4G57S300T5M3(015.5 DRILL) 
G90G0X11.Y97.Z400. 
G43Z80.H4M16 
G83Z-30.Q2.R2.F80
/X-11.Y-97.
G0G49Z400.H00
G91G28Z0M6 
N5G57S200T6M3(023. CORE DRILL) 
G90G0X11.Y97.Z400. 
G43Z80.H5M16 
G73Z-28.Q1.R1.F150 
/X-11.Y-97.
G0G49Z400.H00
G91G28Z0M6 
N6G57S100T1M3(3/4-14 NPT)
G90G0X11.Y97.Z400. 
G43Z80.H6M16 
G84Z-12.R10.F181.428 
/X-11.Y-97.
G0G49Z400.H00M17 
G69
G91G28Y0Z0M6 
M30
                                                                                                                         
O0771
N1G54S100M3
G90G0X0.Y40.325Z350. 
G43Z20.H20 
G83Z-20.Q1.R2.F30
Y-40.325 
G0Z350.H00 
G91G28Z0.Y0. 
M30
                                                                                                                         
O0777
N1G54S500M3
G90G0X0.Y0.Z350. 
G43Z20.H10M16
G1Z-3.F120 
X-50.
G0Z0.
X0.
G1Z-4.F120 
X-50.
G0Z0.
X0.
G1Z-5.F120 
X-50.
/G0Z0. 
/X0. 
/G1Z-4.F120
/X-50. 
/G0Z0. 
/X0. 
/G1Z-5.F120
/X-50. 
G0Z400.H00M17
G91G28Z0.Y0. 
M30
                                                                                                                         
O4009(SELECTORVALVEHORISONTAL) 
M98P1(02/06/04)
(M2402.01-.05)(HOUSINGWIDTH48.)
(JIG)(863.00)(X-24.5)
(G58X)(Y-281.05)(Z-423.) 
(G59 Z-488.25) 
M00(1-90)
GOTO42 
N1G58S450T2M3(SAE-10L) 
G90G0X0.Y20.5Z300. 
G43Z10.H1M16 
G82Z-26.5P500R6.F40
Y-20.5 
G0G49X-100.Z400.H00
G91G28Z0M6 
N2G58S150T1M3(7/8-14)
G90G0X0.Y20.5Z300. 
G43Z10.H2M16 
G84Z-19.5F272.1428 
Y-20.5 
G0G49X-100.Z400.H00M17 
G91G28Z0Y0M6 
M30
M00(2-180) 
N3G59S900T4M3(SEL.SIDEBARSSW)
G90G0X0.Y70.2Z300.(Y69.5)
G43Z30.H3M16 
G82Z0.P500R10.F60
Y-70.2 
G0G49X-100.Z400.H00
G91G28Z0M6 
N4G59S600T5M3(018.8B/BAR)
G90G0X0.Y70.2Z350. 
G43Z30.H4M16 
G73Z-93.Q5.R2.F60
Y-70.2 
G0G49X-100.Z400.H00
G91G28Z0M6 
N5G59S600T3M3(45 ISCAR)
G90G0X0.Y70.2Z300. 
G43Z30.H5M16 
G82Z-4.4P500R0.F30 
Y-70.2 
G0G49X-100.Z400.H00
G91G28Y0.Z0M6
M17
M30
GOTO32 
 
M00(3-270)(3RDPORT)
N42G58S550T2M3(015.5DRILL) 
G90G0X0.Y0.Z300. 
G43Z50.H1M16 
G83Z-42.Q2.R5.F80. 
G0G49X-100.Z400.H00
G91G28Z0M6 
N1G58S450T3M3(SAE10) 
G90G0X0.Y0.Z300. 
G43Z50.H2M16 
G82Z-25.5P500R5.F40
G0G49X-100.Z400.H00
G91G28Z0M6 
N2G58S150T1M3(7/8-14)
G90G0X0.Y0.Z300. 
G43Z50.H3M16 
G84Z-17.R10.F272.14
G0G49X-100.Z400.H00M17 
G91G28Z0.Y0.M6 
M30
M00(4-360) 
N32G59S900T5M3(SEL.SIDEBARSSW) 
G90G0X0.Y-70.2Z300.
G43Z30.H3M16 
G82Z0.P500R10.F60
Y70.2
G0G49X-100.Z400.H00
G91G28Z0M6 
/N4G59S320T5M3(018.8B/BAR) 
/G90G0X0.Y-69.5Z300. 
/G43Z30.H4M16
/G81Z-46.I0.1R2.F60
/G0G49X-100.Z400.H00 
/G91G28Z0M6
N5G59S600T3M3(45 ISCAR)
G90G0X0.Y-70.2Z300.
G43Z30.H5M16 
G82Z-4.4P500R0.F30 
Y70.2
G0G49X-100.Z400.H00M17 
G91G28Y0Z0M6 
M00(50)
M30
                                                                                                                         
O7505(INLET SIDE 010.) 
M98P1(4/97)
(DATUM X-130. Y50.)
(G57 Z-638.7)
N1G57S600T2M3(C DRILL) 
G90G0X0.Y58.5Z350. 
G43Z10.H1M16 
G81Z-12.R-4.F60
X-22.Y-20. 
X22. 
G0Z400.H00 
G91G28Z0M6 
N2G57S700T3M3(010. DRILL)
G90G0X0.Y58.5Z400. 
G43Z10.H2M16 
G83Z-51.Q3.R-4.F80 
X-22.Y-20. 
X22. 
G0Z400.H00 
G91G28Z0M6 
N3G57S600T1M3(022.)
G90G0X0.Y58.5Z350. 
G43Z10.H3M16 
G82Z-9.5P50R2.F20
X-22.Y-20. 
X22. 
G0Z400.H00M17
G91G28Y0.Z0.M6 
M30
                                                                                                                         
O7506(V75 OUTLET POWER BEYOND) 
M98P1(06/05) 
(G57 Z-648.) 
N1G57S600T2M3(C DRILL) 
G90G0X0.Y58.5Z350. 
G43Z10.H1M16 
G81Z-24.R-16.F60 
X-22.Y-20. 
X22. 
G0Z400.H00 
G91G28Z0M6 
N2G57S700T3M3(010. DRILL)
G90G0X0.Y58.5Z400. 
G43Z10.H2M16 
G83Z-44.Q3.R-16.F80
X-22.Y-20. 
X22. 
G0Z400.H00 
G91G28Z0M6 
N3G57S600T4M3(022.)
G90G0X0.Y58.5Z350. 
G43Z10.H3M16 
G82Z-21.5P50R-10.F20 
X-22.Y-20.R2.
X22. 
G0Z400.H00 
G91G28Z0.M6
N4G57S400T5M3(14. DRILL) 
G0G90X0.Y0.Z300. 
G43Z50.H4M16 
G83Z-42.Q4.R-20.F40. 
G0Z400.H00 
G91G28Z0.M6
N5G57S450T6M3(SAE12 BAR) 
G0G90X0.Y0.Z300. 
G43Z20.H5M16 
G82Z-34.5P50R2.F30 
G0Z400.H00 
G91G28Z0.M6
N6G57S150T1M3(1.1/16 12) 
G0G90X0.Y0.Z300. 
G43Z20.H6M16 
G84Z-19.5R10.F317.5
G0Z400.H00M17
G91G28Z0.Y0.M6 
M30
                                                                                                                         
O7507(V75RELIEF.PATTERN) 
M98P1
(DATUM)(X126. Y39.)(Z-643.55)
(X127.5 Y47.)(-640.1)
(OUTLET Z-648.66)
N1G57S1200T22M3(ISCAR 45)
G90G0X0.Y0.Z300. 
G43Z10.H21M8 
M98P7508 
M71
M98P7508 
M70
G0Z400.H00 
G91G28Z0M6 
M98P7509 
M30
                                                                                                                         
O7508(7507 SUB PROG) 
G90G0X27.Y20.Z2. 
G1Z-1.F80M16 
X23.Y0.F150
Y-4. 
X29.5
Y0.
G02X40.7Y20.R23.5
G1X21.84Y35.35 
G02X11.87Y19.7R22. 
G02X23.Y0.R23. 
G0Z10. 
X0.Y0. 
M70
M99
 
 
                                                                                                                         
O7509(O-RING)
M98P1
(DATUM)(X MIDDLE)(Y 39. FROM BOTTOM) 
N2G57S380T23M3(025 O-RING) 
G90G0X0.Y37.6Z400.(Y38.) 
G43Z10.H22M16
G82Z-2.1P50R2.F20
(Y-0.5)
G0Z400.H00 
G91G28Z0M6 
N3G57S380T21M3(028 O-RING) 
G90G0X-53.5Y0.Z350.
G43Z10.H23M16
G82Z-2.1P50R2.F20
X0.Y-0.5(Y-0.5 C/S)(Y0.) 
X53.5Y0. 
G0Z400.H00M17
G91G28Y0.Z0.M6 
M30
                                                                                                                         
O7510(010.DRILL) 
M98P1
(DATUM)(MIDDLE)
N1G54S1200T2M3(C DRILL)
G90G0X-57.15Y61.Z350.
G43Z10.H1M16 
G81Z-5.R2.F40. 
X57.15 
X0.Y58.5 
X-22.Y-20. 
X22. 
G0G49Z400.H00
G91G28Z0M6 
N2G54S500M3T1(010. DRILL)
G90G0X-57.15Y61.Z400.
G43Z10.H2M16 
G83Z-12.Q3.R2.F70
X57.15 
X0.Y58.5Z-51.
X-22.Y-20. 
X22. 
G49G0Z350.H00M17 
G91G28Z0Y0.M6
M30
M99
%